Playing with PIC18F4550 : write and compile C code , upload HEX to it

Share the joy
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  

Well, I’d love to discover new thing and try something new just to learn how it work.
That’s one of the thing that I wish will remain even after growing up and being old man . ๐Ÿ˜›

So, I’d ordered some stuff from http://www.cytron.com.my at few months back.
At that time, it mainly because I need its “Programmer” connector to upgrade the firmware into one of the
chip we used in my office’s research / test component.
Instead of just ordering for the cable, I order the whole start-up kit.
Or more precisely , I bought the โ€œFinal Year Project Starter Pack 02โ€ from cytron.com.my.
(oh..btw, I didn’t claim any single cent from the office for this one.. therefore,the whole set are rightfully mine. :P)

After the connector is no longer needed, as it was just to upgrade the firmware on one of our RnD board.

After almost a year,I opened up the box and start looking at it.
Then I thought why not just open the box and write something like.
“Writing C code,compile to HEX and getting it into a micro-controller chip with PIC18F4550″‘.
I spend first few hour to get everything hook up correctly and successfully wrote something on it. :)

This starter pack includes the PIC microcontoller, LED as output, push button as input, multi meter for troubleshooting and verification, programmer and bread board. A comprehensive set to start for me.

Package Include:
 
    SK40C x 1
    PIC18F4550 x 1
    UIC00B Programmerx 1
    AC-DC Adaptor TMC-500PM x 1
    Digital Multimeter x 1
    Bread Board x 1
    LED 3mm x 10
    Push Button x 5
    Jumper Wire x 5m
    Resistor 330R x 10
    Resistor 1K x 10
    Resistor 10K x 10

So, I connected everything starting with .

Putting PIC18F4550 IC(microcontroller chip) into SK40Cโ€™s IC slot.

and. this the programmer interface ..”UIC00B.”

Then, UIC00B Programmer interface to USB port on the PC.

Then connect SK40C to UIC00B Programmer interface . (rainbow cable)

Then, ready to go.. :)

There is avalaible tutorial video how to connect all this.

Aha. before that, I just need to install some software on my computer first.

The list are:

1.MPLab IDE. (v8.46)
2.PICKit 2 (v2.61)
3. MPLAB C for PIC18 MCUs.

Some of the software are provided inside the CD that come together with the Packages.
except for the Hi-Tech C compiler which I failed to use its Lite version.
So, I downloaded the “MPLAB C for PIC18″ lite version from microchip website.
Which run beautifully without problem..

Here , how I start.

MPLAB IDE interface is as follows.

Start with new project wizard.

then it would become something like this.
at which I can add files and more thing into it.

First thing I add is the header for this CHIP , sitting somewhere at “C:Program Files (x86)Microchipmplabc18v3.40h>”:

19/02/2011  04:37 AM            54,114 p18lf46j11.h
19/02/2011  04:37 AM            72,158 p18lf46j13.h
01/06/2011  04:23 AM            64,045 p18lf46j50.h
19/02/2011  04:37 AM            79,095 p18lf46j53.h
19/02/2011  04:37 AM            68,756 p18lf46k22.h
19/02/2011  04:37 AM           159,899 p18lf46k80.h
19/02/2011  04:37 AM            72,158 p18lf47j13.h
19/02/2011  04:37 AM            79,095 p18lf47j53.h
19/02/2011  04:37 AM           163,094 p18lf65k80.h
19/02/2011  04:37 AM           163,094 p18lf66k80.h
09/06/2011  05:36 PM           315,200 pconfig.h
18/06/2009  06:21 PM            22,649 pcpwm.h
19/02/2011  04:37 AM            31,340 pmcv20usb.h
04/06/2010  12:43 PM            35,211 pmp.h
18/06/2009  06:21 PM             7,847 portb.h
24/12/2009  12:03 PM            17,334 pps.h
19/12/2008  04:33 PM             2,166 ProMPT.h
10/08/2010  08:57 PM            29,949 pwm.h
19/12/2008  04:33 PM               940 reset.h
04/06/2009  02:21 PM            20,747 rtcc.h
10/12/2003  06:54 AM               670 setjmp.h
19/07/2009  07:21 AM            19,926 spi.h
05/08/2004  02:46 AM               302 stdarg.h
05/08/2004  02:52 AM             1,883 stddef.h
02/10/2004  02:48 AM             1,024 stdio.h
10/12/2003  06:54 AM             6,331 stdlib.h
10/12/2003  06:54 AM            35,401 string.h
18/06/2009  06:21 PM             5,860 sw_i2c.h
18/06/2009  06:21 PM             4,416 sw_spi.h
18/06/2009  06:21 PM             2,903 sw_uart.h
22/12/2010  12:08 PM            52,966 timers.h
18/06/2009  06:21 PM            19,970 usart.h
05/05/2009  01:25 PM             4,165 xlcd.h
             321 File(s)     17,139,562 bytes
               2 Dir(s)  188,943,335,424 bytes free
 
C:\Program Files (x86)\Microchip\mplabc18\v3.40\h>

Adding it so that I didn’t have to re-define the whole port for the PIC18F4550 manually . ๐Ÿ˜›
To use .. I just define to include those file header into my c code.

#include <p18F4550.h>
#include <delays.h>
 
#pragma config FOSC = INTOSCIO_EC //Internal oscillator, port function on RA6, EC used by USB
#pragma config WDT = OFF //Disable watchdog timer
 
 
#define    LED1    LATBbits.LATB6
#define    LED2    LATBbits.LATB7
void main(void)
{
    unsigned char i;
 
    //init();   		 // initialise PIC
    TRISBbits.TRISB0=1;   	 //configure PORTB I/O direction as output
    TRISBbits.TRISB1=1;   	 //configure PORTB I/O direction as output
    TRISBbits.TRISB6=0;   	 //configure PORTB I/O direction as input in case want to use SWitch1
    TRISBbits.TRISB7=0;   	 //configure PORTB I/O direction as input in case want to use SWitch2
 
 
	 LED1 = 0;//Set LED Pin
    LED2 = 1;//Set LED Pin
 
    while(1)
    {
    // on both
    Delay10KTCYx(25);	// delay 200ms
    LED1 ^=1;
    LED2 ^=1;
    }
}

some setting at the “configuration bit.”

Disabling the “watchdog” and “low voltage ”


then try to build it out. ;P

then time to connect and upload it to the real chip.
this can be done in two different way..

One .. get it to generate the HEX code, and manually use PicKit 2 to write into the chip.
however.. to save the configuration bit.. from the MPLAB IDE.. use the File -> Export .
then the HEx will be generated.

From there.. just run PIC Kit 2 and .. connect the PIC programmer cable, rainbow cable, power on everyting,
at PIC Kit 2-> Tools -> check communication , it shall report as connected.
Then.. just File -> Import Hex, then WRITE !.

Other easier way , is to use MPLAB IDE interface .. Programmer -> PIC Kit 2.

then .. set the programmer setting.

then.. just clean .. and rebuild all.

.. with the programmer connected. it would spit something like this.

After that, turn the SK40C off..
disconnect the rainbow cable from SK40C to USB-programmer.

power on the SK40C alone.. then it would run the new HEX as expected. :)

result would be something like..

https://plus.google.com/u/0/113037984437874858904/posts/4o9yWxKFhPR

More details at : http://tutorial.cytron.com.my/2011/08/05/sk40c-tutorial/

p/s : ..for the next thing,maybe is to get the UART connected to a GSM modem, connect the relay to one of the DI, write C code to receive and decode the received SMS.. and act accordingly to turn on/off the relay.. and maybe add the LCD to show status.. relay to be connected to one of electrical appliance. or may be a series of electrical appliance..
then .. maybe get it integrated to a web interface just to encode the SMS to be sent to this device.

Hmm.. only until recently I realize my understanding of Digital Input (DI) is actually reversed of what I thought is Analog Input. . haha.

Sharing is caring
Sharing is caring

About Namran Hussin

a soft spoken guy... with exceptional interest in computers and technology. I love to learn new thing and also love to break thing for the sake of learning.. but I do abide to the self-imposed limitation or certain thing such as social thing in life, thing can be done and thing that must be avoided at whatever cost such as drug,illegal tracking, smoke,illicit activity..etc.muahahaha let's share what we had in this short term of the life.! make it worth of the living.~

8 thoughts on “Playing with PIC18F4550 : write and compile C code , upload HEX to it

  1. mike

    hey can you do a tutorial for interfacing an LCD with the PIC18f4550 using the Hi-Tech C compiler? I’m having a lot of trouble simply getting the LCD to say “Hello World”. Thanks.

  2. rathee

    Hi,
    im a student doing a project with pic18f4550 i wanna use the relay as a switch to on and off the system, can anyone help me in this c programming im very bad in programming…
    thanks in advance…

  3. xinlin_7

    Hello there,
    The PIC18F4550 I am using is a different model from yours, mine is a TQFP structure. If I follow the general connections, use the PickIt 2 to load my hex code into the microcontroller, it should be possible to work right?

    Hope to hear from you soon. Thank you.

  4. the hobbit gaming

    Choose up a pack of them and allow your creativity operate wild.

    Given the phenomenon that “The Lord of the Rings” trilogy was, the expectations for the film version of “The Hobbit” are understandably high.
    The new 2011 HBO medieval fantasy television series “Game of Thrones” has become an instant mega hit show.

  5. site

    It is already a known fact that the iPhone’s battery doesn’t last
    very long, so a battery extender for the iPhone is a must for your iPhone.
    Before you start, you need to turn off your iTunes helper program because that program would have a significant
    effect in your operation. As outlined by iPhone app development gurus, consumers wouldn’t receive any guidance in situation of crisis if the enterprise confirms that the device is jail-broken.

Comments are closed.

%d bloggers like this: